Instruments set

S.T.I.F. SAS has developed a specific instrument kit, adapted to reconstructive surgery of ligament and tendon injuries with VETLIG GLOBAL synthetic implants.
This kit can also be used for other orthopaedic surgeries
S.T.I.F. SAS has developed a specific instrument kit, adapted to reconstructive surgery of ligament and tendon injuries with VETLIG GLOBAL synthetic implants.
This kit can also be used for other orthopaedic surgeries
4 cannulated drills: 2.5 mm, 3 mm, 3.6 mm, and 4.2 mm for primary tunnels
3 non-cannulated drills: 3.5mm, 4mm and 4.5mm for transversal tunnels
2 x 2 mm sharp pins with two trocar tips used as guides for 3.6 mm and 4.2 mm cannulated drills
2 x 0.9 mm sharp pins with two trocar tips used as guides for 2.5 mm and 3 mm cannulated drills
2 x 2 mm blunt pins
2 x 0.9mm blunt pins used as guides for 3mm, 3.5mm, 4mm and 4.5mm screws
2 x 2.5 mm hexagonal pins used as guides and screwdrivers, for 5 mm and 6 mm screws
1 set of 3 telescopic tubes of 6mm, 8mm and 10mm as protective sleeves to protect soft tissue during drilling, when necessary
2 passing tubes: 2.5 mm and 3.5 mm to allow the passage of stainless steel wire loop
4 stainless steel wire loops to pull the ligament traction wires through the tunnels
A silicone screwdriver handle, allowing the insertion of the three types of tips specific to cannulated screws:
A 1 mm cannulated hexagonal screwdriver tip for 3 mm and 3.5 mm screws (guided by the 0.9 mm pin)
A male hexagonal screwdriver tip, cannulated at 1 mm for 4 mm and 4.5 mm screws (guided by the 0.9 mm pin)
A female cannulated screwdriver tip suitable for the hexagonal pin, used for 5mm and 6mm screws
4 cannulated drills: 2.5 mm, 3 mm, 3.6 mm, and 4.2 mm for primary tunnels
3 non-cannulated drills: 3.5mm, 4mm and 4.5mm for transversal tunnels
2 x 2 mm sharp pins with two trocar tips used as guides for 3.6 mm and 4.2 mm cannulated drills
2 x 0.9 mm sharp pins with two trocar tips used as guides for 2.5 mm and 3 mm cannulated drills
2 x 2 mm blunt pins
2 x 0.9mm blunt pins used as guides for 3mm, 3.5mm, 4mm and 4.5mm screws
2 x 2.5 mm hexagonal pins used as guides and screwdrivers, for 5 mm and 6 mm screws
1 set of 3 telescopic tubes of 6mm, 8mm and 10mm as protective sleeves to protect soft tissue during drilling, when necessary
2 passing tubes: 2.5 mm and 3.5 mm to allow the passage of stainless steel wire loop
4 stainless steel wire loops to pull the ligament traction wires through the tunnels
A silicone screwdriver handle, allowing the insertion of the three types of tips specific to cannulated screws:
A 1 mm cannulated hexagonal screwdriver tip for 3 mm and 3.5 mm screws (guided by the 0.9 mm pin)
A male hexagonal screwdriver tip, cannulated at 1 mm for 4 mm and 4.5 mm screws (guided by the 0.9 mm pin)
A female cannulated screwdriver tip suitable for the hexagonal pin, used for 5mm and 6mm screws